G. Atmeh, F. Darwish, and Z. Hasan
Jordan University of Science and Technology, Irbid, Jordan
Texas A&M University, College Station, TX, USA
The present study focuses on the design and analysis of a single-engine, propeller-driven general aviation airplane. Initial weight estimation based on the initial sketch and the design mission profile is conducted. The estimated weight and other design parameters are used to define the external geometry of the fuselage, wing and tail. Conic lofting is utilized to render a layout of the design ...
A. Polit, R. Jez
ABB Corporate Research Center, Krakow, Poland
The air gap is one of the most crucial part of magnetic circuits, especially in high-power inductors. It significantly modifies the parameters of magnetic devices by increasing the saturation current, linearizing B-H curve of magnetic circuit and causing a decreasing in the inductance. Therefore the optimal selection of shape and dimensions of the air gap is very important from the design point ...
G. R. Prakash, K. M. V. Swamy, S. Huddar, B. G. Sheeparamatti, Kirankumar B. B.
Basaveshwar Engineering College, Bagalkot, Karnataka, India
The focus of this paper is to study the effect on resonance frequency and power enhancement techniques of piezoelectric MEMS and modeling, design, and optimization of a piezoelectric generator based on a two-layer bending element(Figure 1) using COMSOL Multiphysics. An analytical relation was developed based on the shift in resonance frequency(Figure 2) caused by the addition of a thin film ...
J. Crompton, S. Yushanov, K. Koppenhoefer
AltaSim Technologies, Columbus, OH, USA
The Mie solution to the scattering of electromagnetic waves by spherical particles has been examined using COMSOL Multiphysics®. The results assume elastic scattering only and do not include Brillouin or Raman scattering. The nature of the interaction has been considered for materials with three different properties: metallic, magnetic and dielectric. The solutions provide details of the ...
O. Vogel, and J. Ulm
Proportional solenoids are well-known and used in a wide range of applications today. This paper is about methods of influencing the characteristic force-stroke-curves of magnetic actuators by means of different pole geometries. The conical design of the stator pole which is mostly used to accomplish proportional solenoids is analyzed by both a simple analytic reluctance model and a FEM model ...
Implementation of the Perfectly Matched Layer to Determine the Quality Factor of Axisymmetric Resonators in COMSOL
M.I. Cheema, and A.G. Kirk
McGill University, Montreal, QC, Canada
Due to the inseparability of the wave equation, numerical methods are needed to develop an accurate electromagnetic model for various axisymmetric resonators such as micro-discs and micro-toroids. Our purpose is the implementation of a perfectly matched layer to determine the quality factor of axisymmetric resonators with high accuracy in COMSOL. We treated the perfectly matched layer as an ...
J.S. Crompton, L.T. Gritter, S.Y. Yushanov, and K.C. Koppenhoefer
AltaSim Technologies LLC, Columbus, OH, USA
Analysis of burning candles is extremely complex; combustion produces a highly non-linear temperature profile through the flame in which local temperatures may exceed 1400 °C. Heat transfer includes radiation, conduction and convection components and the low melting point of the candle wax leads to a phase change that allows mass transport via capillary flow prior to combustion in the flame. ...
Y.F. Wang, Y.S. Wang, L. Wang
Institute of Engineering Mechanics, Beijing Jiaotong University, Beijing, China
Department of Mechanical Engineering, Østfold University College, Halden, Norway
We show in this paper that by careful design of the geometry of the resonators, complete bandgap with relatively low center frequency can be obtained for 2D and 3D Phononic Crystals with resonators. The generation of the bandgap is due to the local resonance of the unit cell. Spring-mass and spring-pendulum models are developed to predict the boundaries of the complete bandgap. The predicted ...
P. L. Mills , K. Barman , S. Mothupally , A. Sonejee ,
 Texas A&M University - Kingsville, Kingsville, TX, USA
Introduction Fluid flow patterns in research or process-scale equipment where a fluid is contained between concentric rotating cylinders in the absence of bulk axial flow has received notable attention in the field of fluid mechanics. Annular flows occur in many practical applications, such as in the production of oil and gas, fluid viscometers, centrifugally-driven separation processes, ...
Exploratory FEM-Based Multiphysics Oxygen Transport and Cell Viability Models for Isolated Pancreatic Islets
Diabetes Research Institute and the Department of Molecular and Cellular Pharmacology, University of Miami, Miller School of Medicine, Miami, FL, USA
Cellular-level oxygen consumption and cell viability models incorporating physiologically realistic assumptions and fully scaled 2D/3D geometries have been implemented in COMSOL Multiphysics for isolated pancreatic islets. Oxygen consumption was assumed to follow Michaelis-Menten–type kinetics and to cease when local concentrations fell below a critical threshold. Results are in good agreement ...