Variable Capacitance And Pull-In Voltage Analysis Of Electrically Actuated Meander-Suspended Superconducting MEMS
N. AlCheikh, P. Xavier, J.M. Duchamp, C.H. Boucher, and K. Schuster
Institute of Microelectronics, Electromagnetism and Photonics (IMEP-LAHC), Minatec, Grenoble, France
Institute of Millimetric Radio Astronomy (IRAM), Grenoble, France
Variable capacitors between the fF and pF range are very interesting for high frequency applications like variable filters, resonators, etc. For radio astronomy applications variable capacitors, realized by electrostatically actuated, micromechanical Meanders-suspended bridges (MEMS) made of superconducting Niobium, have been measured to find C(V). A non plane capacitance behavior have been ...
Optimization of Design Parameters of a Novel MEMS Strain Sensor used for Structural Health Monitoring of Highway Bridges
H. Saboonchi, and D. Ozevin
Civil Engineering Department
University of Illinois at Chicago
The novel Micro Electro Mechanical System (MEMS) based Piezoresistive stain sensor is presented in this paper. The main goal of this sensor is to monitor the localized strain in the highway bridges especially near the crack tips. Monitoring the crack growth on the bridges can lead to early detection and prevention of bridge failures. The COMSOL Multiphysics software was used to optimize the ...
P. K. Podder, D. Mallick, D. P. Samajdar, and A. Bhattacharyya
Institute of Radio Physics and Electronics
University of Calcutta
West Bengal, India
In this paper, we have addressed the issues related to the design and simulation of MEMS based silicon micro-needles for insertion of fluid into the dermis layer and into the subcutaneous fat layer. In addition, a poly-silicon micro-pump based on the principle of electrostatic actuation has been designed and simulated which can be integrated with the proposed micro-needles to control the fluid ...
J. Muraoka, and T. Suzuki
Yamagata Research Institute of Technology
The traveling wave ultrasonic vibration disks for dispersion of particles were designed by using of FEM analysis. The vibration disks are required specific vibration pattern, which contains three nodal lines. The vibration disk thickness was calculated to be matched the resonance frequency of bolted langevin type transducer and the specific vibration pattern. The alignment of the transducer was ...
S. Harrison, M. Young, M. Hayne, P. D. Hodgson, R. J. Young, A. Strittmatter, A. Lenz, U. W. Pohl, D. Bimberg
Department of Physics, Lancaster University, Lancaster, UK
Institut für Festkörperphysik, Berlin, Germany
Low-dimensional semiconductor nanostructures, in which charge carriers are confined in a number of spatial dimensions, are the focus of much solid-state physics research, offering superior optical and electronic properties over their bulk counterparts. Both two-dimensional (2D) and zero-dimensional (0D) structures have seen wide-ranging applications in laser diodes, solar cells and LEDs to name ...
AC Electrothermal Characterization of Doped-Si Heated Microcantilevers Using Frequency-Domain Finite Element Analysis - new
K. Park, S. Hamian, A. M. Gauffreau, T. Walsh
Mechanical Engineering Department, University of Utah, Salt Lake City, UT, USA
Department of Mechanical, Industrial & Systems Engineering, University of Rhode Island, Kingston, RI, USA
This work investigates the frequency-dependent electrothermal behaviors of freestanding doped-silicon heated microcantilever probes operating under the periodic (ac) Joule heating. The transient heat conduction equation for each component (i.e., the low-doped heater region, the high-doped constriction region, and the high-doped leg region) is solved using the general heat transfer module for DC ...
M. Guizzetti, V. Ferrari, D. Marioli, and T. Zawada
Dept. of Electronics for Automation, University of Brescia, Brescia, Italy
Meggitt, Ferroperm Piezoceramics A/S, Kvistgaard, Denmark
The conversion of mechanical energy from environmental vibrations into electrical energy is a key point for powering sensor nodes toward the development of autonomous sensor systems. Piezoelectric energy converters realized in a cantilever configuration are the most studied for this purpose. In order to improve the performances of the converter, the geometry has to be properly designed. In this ...
R. Nithya, K. Kavitha, R. K. Shahana, A. Gupta, M. Alagappan
Department of Biomedical Engineering, PSG College of Technology, Coimbatore, Tamilnadu, India
The primary function of the vestibular system is to provide the brain with information about the body\'s motion and orientation. The absence of this information causes blurred vision and spatial disorientation, vertigo, dizziness, imbalance, nausea, vomiting, and other symptoms often characterize dysfunction of the vestibular system. Our aim is to design vestibular prosthesis using COMSOL ...
A. G. S. Barreto Neto , A. M. N. Lima , C. S. Moreira ,
 Instituto Federal de Ciência e Tecnologia - IFPB, João Pessoa, PB, Brasil
 Universidade Federal de Campina Grande - UFCG, Campina Grande, PB, Brasil
Este trabalho trata do dimensionamento da estrutura bocal/difusor utilizando a simulação computacional com fronteira móvel. Esse tipo de simulação contempla toda estrutura da bomba, isto é, câmara de bombeamento, difusor e área de dispersão de fluxo, de modo a contabilizar o refluxo em função da estrutura, possibilitando um projeto mais realísticos da estrutura.
J. Dsa, Manisha, M. Goswami , B.R Singh ,
 Indian Institute of information technology Allahabad, Allahabad, Uttar Pradesh, India
We have developed a piezoelectrically controlled MEMS drug delivery device for on-demand release of defined quantities of drug. A drug-loaded micro reservoir (∅6mm×550µm) is sealed by A membrane placed over the drug reservoir on which the piezoelectric material is deposited. On application of voltage across this piezoelectric material , the membrane deflects allowing the fluid to fill into the ...