Technical Papers and Presentations

Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.

Design of MEMS Based High Sensitivity and Fast Response Capacitive Humidity Sensor

R. Karthick, S. P. K. Babu, A. R. Abirami, and S. Kalainila
Periyar Maniammai University
Periyar Nagar
Vallam, Thanjavur
Tamilnadu, India

This paper presents the design and simulation of high sensitivity and fast response capacitive humidity sensor. Generally, the capacitive humidity sensor is made up of parallel electrode, the upper electrode being a grid with various line width and line spacing. A model is simulated using COMSOL Multiphysics. High sensitivity and fast response of the model is optimized by varying the ...

Simulation of a One-Port SAW Resonator using COMSOL Multiphysics

R. Krishnan, H.B. Nemade, and R. Paily
Indian Institute of Technology, Guwahati

In this paper, we discuss simulation of one-port Surface Acoustic Wave (SAW) resonators using COMSOL Multiphysics. Resonator action can be achieved in one of the two ways; a single Inter-digital Transducer (IDT) having several fingers over a piezoelectric substrate or a short IDT with reflecting gratings at the ends of the IDT. We have modeled a Rayleigh wave type SAW device choosing YZ ...

Using COMSOL Multiphysics Capability for Engineering High Q MEMS Resonators

Amy Duwel
Charles Stark Draper Laboratory
Cambridge, USA

Micromechanical resonators are used in a wide variety of applications, including inertial sensing, chemical and biological sensing, acoustic sensing, and microwave transceivers. Despite the distinct design requirements for each of these applications, a ubiquitous resonator performance parameter emerges. This is the resonator’s Quality factor (Q), which describes the mechanical energy damping. ...

Design and Simulation of 3D MEMS Piezoelectric Gyroscope using COMSOL Multiphysics®

T.Madhuranath[1], R.Praharsha[1], Dr.K.Srinivasa Rao[1]
[1]Lakireddy Bali Reddy College of Engineering, Mylavaram, Andhra Pradesh, India

MEMS is the leading technology which combines both electronic and mechanical devices on a single microchip. Tracing the position of the object is an important problem in engineering. This can be addressed by Gyroscopes. These sensors are used to find orientation and angular velocity. This paper focuses on 3D MEMS Piezoelectric Gyroscope. COMSOL Multiphysics® is used for designing and ...

Numerical Modeling of Dielectrophoretic Forces Acting upon Biological Cells in Silicon Lab-On-Chip Devices

S. Burgarella, M. Bianchessi, and M. De Fazio
Advanced System Technology, R&I e-Health, STMicroelectronics, Agrate Brianza, Italy

Dielectrophoresis (DEP) is a promising method for the automated separation of biological cells in a miniaturized format. This technology allows cells to be manipulated electronically while suspended in a microfluidic channel embedded in a silicon lab-on-chip. In this work, several dielectrophoretic configurations have been designed and fabricated using micro-electro-mechanical-systems (MEMS) ...

Implementation of ALE Moving Mesh for Transient Modeling of Nanowire Trajectories Caused by Electrokinetic Forces

S.M. Davison, and K.V. Sharp
Pennsylvania State University

Moving nanowires through microfluidic channels under electrokinetic forces can be a valuable technique to aid in the fabrication of certain devices. The trajectories of a nanowire under the influence of an externally applied electric field have been modelled through a straight channel, through a converging channel, and around a 90° corner. In a straight channel, a nanowire initially ...

2D Simulation of Cardiac Tissue

S. Esfahani[1]
[1]University of South Florida, Tampa, FL, USA

A two-dimensional atrial tissue model has been constructed in COMSOL Multiphysics® software to study the propagation of action potential and electrograms. The model presents the atrial electrograms recorded with a mapping catheter. A 2D atrial tissue model is simulated using the Courtemanche et al. cell model equations. PDE in coefficient form was used in COMSOL Multiphysics® to reproduce ...

Parametric Study of Polyimide - Lead Zirconate Titanate Thin Film Cantilevers for Transducer Applications

A. Arevalo[1], I.G. Foulds[1]
[1]King Abdullah University of Science and Technology, Thuwal, Kingdom of Saudi Arabia

The simulation of the piezoelectric actuation of the micro-cantilever is presented. Lead Zirconate Titanate (PZT) was chosen for the device fabrication design, due to its thin film processing flexibility. Four layers compose the cantilever structures presented in this work: PZT (piezoelectric material), Platinum (electrodes) and Zirconium Oxide as the buffer layer for the PZT film and polyimide ...

COMSOL Multiphysics Simulations of Microfluidic Systems for Biomedical Applications

M. Dimaki, J. Moresco Lange, P. Vazquez, P. Shah, F. Okkels, and W. Svendsen
Department of Micro- and Nanotechnology, Technical University of Denmark, Lyngby, Denmark

The need for fast, easy and cost-effective analysis of blood samples as well as our understanding of the functionality of cells and neurons are two rather pressing issues in the modern world. Both of these can be addressed by functional lab-on-a-chip systems, which have been designed and optimized for specific analyses. This paper deals with the design of several different systems for cell ...

Design and Simulation of Valveless Piezoelectric Micropump

L. Nayana[1], P. Manohar[1], S. Babu[1]
[1]Department of Electrical Engineering, Visvesvaraya Technological University, Bangalore, Karnataka, India

In this paper some discrete parts of a valveless piezoelectric micropump for drug delivery system is designed and simulated. The core components of the micropump are actuator unit that converts the reciprocating movement of a diaphragm actuated by a piezoelectric actuator into a pumping effect and Nozzle/diffuser elements that are used to direct the flow from inlet to outlet. Simulations are ...

Quick Search