Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.

Three Dimensional Modeling of PEM Fuel Cells with Current Collection from the Gas Diffusion Layer

R. Pushpangadan[1], A. Soman[2], Arundas R.[2], N. G. Thoppan[2], S. P. Duttagupta[1]
[1]Department of Electrical Engineering, Indian Institute of Technology Bombay, Mumbai, Maharashtra, India
[2]College of Engineering, Munnar, Kerala, India

PEM fuel cells are very promising for portable applications. A key component of fuel cell is the flow field plate through which hydrogen will reach the anode, oxygen will reach the cathode and electron collection. Flow field plate made of silicon is not a good electrical conductor , so electrical contacts has to be attached to the Gas Diffusion Layer (GDL) for taking the power to outside ...

Effect of Conductivity and Viscosity in the Velocity Characteristics of a Fluid Flow Induced by Nonuniform AC Electric Field in Electrolytes on Microelectrodes

P. Parikh[1], A. Sethi[1], S. Benedict[1], D. N. Prasad[1], B. Mallik[2], S. Kapur[1], S. Deb[1], S. Banerjee[1]
[1]BITS Pilani Hyderabad Campus, Hyderabad, Andhra Pradesh, India
[2]Megnadh Saha Institute of Technology, Kolkata, India

Electrokinetic transport of fluids has been investigated both experimentally and numerically due to its various applications in microfluidic devices [1-5]. These devices offer the advantage of transporting fluids or particles to specific locations without the aid of mechanical components. The device by Green et al consists of a symmetric arrangement of CPE subjected to an AC potential [6-8]. The ...

Study of Effect on Resonance Frequency of Piezoelectric Unimorph Cantilever for Energy Harvesting

G. R. Prakash[1], K. M. V. Swamy[1], S. Huddar[1], B. G. Sheeparamatti[1], Kirankumar B. B.[1]
[1]Basaveshwar Engineering College, Bagalkot, Karnataka, India

The focus of this paper is to study the effect on resonance frequency and power enhancement techniques[1] of piezoelectric MEMS and modeling, design, and optimization of a piezoelectric generator based on a two-layer bending element(Figure 1) using COMSOL Multiphysics. An analytical relation was developed based on the shift in resonance frequency(Figure 2) caused by the addition of a thin film ...

Transport of Vocs through Bioflim in Biotrickling Filters

Balasubramanian P[1]
[1]Indian Institute of Technology Madras, Chennai, Tamil Nadu, India

Realising the interlinkage of nature and engineering are of paramount essential while comprehending the basics of system’s performances. Application of biotechniques in air pollution control is one such emerging scientific area, where the understandings of these complex systems demand more utilisation of computing softwares. Recently, biofiltration is a versatile biological air pollution control ...

Analysis of Electroosmotic Flow of Power-law Fluids in a Microchannel(1D)

K. SriNithin[1]
[1]IIT Kharagpur, Kharagpur, West Bengal, India

Electroosmotic flow of power-law fluids in a slit channel(1D) is analyzed. The governing equations are the Poisson–Boltzmann equation, the Cauchy momentum equation, Generalized Smoluchowski equation and the continuity equation are used to get shear stress, dynamic viscosity, and velocity distribution. Simulations are performed to examine the effects of ?H, flow behavior index, double layer ...

A MEMS Condenser Microphone for Consumer Applications

S. Kesari[1], A. Pandit[1], K. Mishra[1], Kaushal B. K.[1]
[1]Electronics and Communication Engineering, Nitte Meenakshi Institute of Technology, Bangalore, India

The MEMS microphone is also called microphone chip or silicon microphone.The pressure sensitive diaphragm is etched directly into a silicon chip by MEMS techniques and is usually accompanied with integrated preamplifier. Most MEMS microphones are variants of the condenser microphone design. The device consists of a polysilicon diaphragm suspended over a single crystal silicon backplate ...

Design and Analysis of MEMS Gyroscope

L. Sujatha[1], B. Preethi[1]
[1]Rajalakshmi Engineering College, Chennai, India

MEMS gyroscope technology provides cost- effective method for improving directional estimation and overall accuracy in the navigation systems. This paper presents a tuning- fork gyroscope (TFG) [1] with a perforated proof mass. The perforated proof mass used in the design enables the reduction of the damping effect. This MEMS based gyroscope was designed using COMSOL Multiphysics 4.2a. This ...

Optimizing the Performance of MEMS Electrostatic Comb-Drive Actuator with different Flexure Springs

S. Gupta[1], T. Pahwa[1], R. Bansal[1], V. Bansal[1], B. Prasad[1], D. Kumar[1]
[1]Electronic Science Department Kurukshetra University, Kurukshetra, Haryana

A new design of electrostatic comb drive actuator is presented in this paper by using different spring designs and with different folded beam lengths. An increased displacement of lateral comb drive actuator will subsequently be accomplished with the same actuation voltage. Stress distribution over different spring designs are simulated by COMSOL 3.5a using a standard comb drive with 4 movable ...

Numerical Study of Navier-Stokes Equations in Supersonic Flow over a Double Wedge Airfoil using Adaptive Grids

V. Gopal[1], R. Kolluru[1]
[1]BMS College of Engineering, Bangalore, Karnataka, India.

Numerical study of aerodynamic characteristics in steady laminar supersonic flow over a double wedge airfoil is carried out using commercially available finite element based CFD tool COMSOL Multiphysics. The aerodynamic characteristics of double wedge airfoil like lift and drag are analyzed by solving Navier-Stokes equations in the flow field for various thickness to chord ratios (t_c) and angle ...

Modelling of Pressure Profiles in a High Pressure Chamber using COMSOL Multiphysics

P. S. Rao[1], C. K. Chandra[1]
[1]Agricultural and Food Engineering Department, Indian Institute of Technology Kharagpur, West Bengal, India

High Pressure Processing (HPP) is a leading non-thermal food processing technology that is often cited as a major technological innovation in food preservation. Although it is very early to place this emerging technology among the list of breakthroughs in food processing, HPP has started to become a viable commercial alternative for pasteurisation of value added fruits, vegetables, meat, and ...

1 - 10 of 83 First | < Previous | Next > | Last