TEL US Holdings, Inc., Technology Development Center, Albany, New York, USA
In this presentation we are dealing with the computational fluid model of a Filament Assisted Chemical Vapor Deposition (FACVD) reactor. Proposed strategy in this study involved several steps: (a) development a computational model for FACVD process capable to describe and obtain with reasonable accuracy all relevant phenomena occurring in the reaction chamber; (b) validation the computational ...
University of Calabria
The aim of the present work is the formulation of a theoretical model describing the transport phenomena involved in a food drying process by a convective oven. The proposed model represents a general and predictive tool capable of describing the real oven’s behavior over a wide range of process and fluid-dynamic conditions. The resulting system of non-linear unsteady-state partial ...
University of South Carolina
In this presentation we introduce the concept of Electrochemical Engineering through simulations in COMSOL Multiphysics. Our special case studies are: • a Parallel Plate Electrochemical Reactor, • a Rotating Ring Disk System, • a 3D Lithium Ion Battery, • a Portable Power System, • a Corroding Surface. These examples are all industrial ones, which shows the power of using ...
R. El Otmani1, M. Zinet1, M. Boutaous1, P. Chantrenne1, and H. Benhadid2
1CETHIL, Université Lyon, Villeurbanne, France
2Laboratoire de Mécanique des Fluides et d'Acoustique, Université Lyon, Ecully, France
During injection moulding of thermoplastic parts, high pressures, velocities and temperatures are experienced by the polymer in the filling phase. The numerical simulation of this phase is a complex task, especially for semi-crystalline polymers, because it involves a coupling between heat transfer, material structural transformation and crystallinity. The aim of this work is to present ...
Study of a Self Heating Process of Tetrafluoroethylene by the Exothermic Dimerization Reaction to Octafluorocyclobutane
M. Beckmann-Kluge, H. Krause, V. Schröder, A. Acikalin, and J. Steinbach
Federal Institute for Materials Research and Testing, Berlin, Germany
Technical University Berlin, Berlin, Germany
The self heating process of Tetrafluoroethylene caused by an exothermic dimerization reaction was studied. The heat of reaction can lead to a thermal explosion by the decomposition of the Tetrafluoroethylene. Different reaction kinetics, including multistep kinetics, were used to describe the mass balance. The COMSOL Chemical Engineering Module was used to perform the simulation which was ...
S. Kumar, and M. Raju
General Motors R&D Center, Warren, MI, USA
Optimal CAE Inc., Detroit, MI, USA
Hydrogen refueling in a metal hydride based automotive hydrogen storage system is an exothermic reaction and hence an efficient heat exchanger is required to remove the heat for fast refueling. In this paper a helical coil heat exchanger embedded in a sodium alanate bed is modeled using COMSOL. Sodium alanate is present in the shell and the coolant flows through the helical tube. A ...
G. Selembo, P. Selembo, J. Stanton, and G. Paulsen
University of North Carolina
Surface aeration systems are used in the wastewater treatment industry for the transfer of oxygen in the activated sludge process. These systems are capital intensive and also require a significant amount of energy to operate. Scale-up and design of these systems is largely empirical, and due to the size of these systems, modifications for experimental testing can be economically prohibitive. ...
ZINK, Imaging Inc.
In this work we have constructed a 2D COMSOL model for the drying of Latex. It is based on a prior 1D model of Kiil, but also includes the effects of a flowing air stream, which is necessary to remove the evaporated water vapor. The model illustrates several features of drying that are not accessible to the 1D model, in particular the a profile in the air/water interface that forms near the ...
C. Anandharamakrishnan, R. Gopirajah, and N. Chhanwal
Central Food Technological Research Institute
Freeze-drying is a popular method of producing shelf stable particulate products and is of particular value for drying thermally sensitive materials (volatiles and biological based), which can be heat damaged by higher temperature methods, such as spray-drying. Porous structures are formed by the creation of ice crystals during the freezing stage, which subsequently sublime during the drying ...
D. Lelièvre, P. Glouannec
Université de Bretagne-Sud, Lorient, France
Drying is an essential step in many manufacturing processes, for it will have an important impact on the product quality. This is why many numerical models have been realized over decades, in order to predict the hygrothermal behavior of porous media during the drying process. In this paper, we present a model allowing to properly simulate the pressure, heat and mass transfer during the drying of ...